# Innokin Gozee coils, which Z Coil suits which draw > Innokin Gozee and its Z Coils from 0.3 to 1.6 ohm, the wattage ranges Innokin publishes and the airflow settings for an MTL or RDL draw. According to its maker, the **Innokin Gozee** takes the whole Z Coil range and anything from 0.2 to 3.5 ohm. On paper that is freedom. In a vape shop it becomes a question with no obvious answer, because a coil pack shows a resistance in ohms and rarely the kind of draw it was built for. Between a tight draw and a looser one, the right coil and the right settings change everything, and the kit's manual only details one coil. ## The Z Coil to fit in your Innokin Gozee, the short answer For a tight mouth-to-lung draw, the 1.2 ohm Z Coil, at 10 to 14 W, and the 1.6 ohm, at 9 to 12 W, are the most consistent choices. For a warmer MTL draw, the 0.8 ohm at 15 to 18 W is the one the Gozee manual quotes. For RDL, Innokin offers the 1.0 ohm at 20 to 25 W, designed for restricted direct-lung vaping, and the 0.3 ohm at 30 to 40 W for a looser draw. Our advice for a measured MTL draw comes down to one value, the 1.2 ohm. It sits in the middle of the MTL options, runs at a moderate wattage and leaves room to adjust either way. ## Z Coils and their wattage, according to Innokin Innokin does not publish a single page for its coils. The figures are spread across the pages of its compatible tanks and kits, and we have gathered them here. | Z Coil | Stated range | Use described by Innokin | |---|---|---| | 0.3 ohm | 30 to 40 W | RDL | | 0.6 ohm DuoPrime | 9 to 13 W | MTL | | 0.8 ohm | 15 to 18 W | MTL, warmer vape needing more wattage | | 1.0 ohm | 20 to 25 W | restricted direct lung or warm MTL | | 1.2 ohm | 10 to 14 W | MTL, redesigned for flavour | | 1.6 ohm | 9 to 12 W | MTL, recommended for nicotine salts | Two rows deserve a closer look. The 0.6 ohm DuoPrime brings Innokin's DuoPrime design to the Z Coil family, and the brand rates it for MTL despite its low value, which breaks the usual rule that a low resistance means an airy draw. The 1.0 ohm, on the other hand, needs more power than the 0.8 ohm. The resistance alone is not enough, then. It is the published wattage range that tells you which draw a coil is meant for. ## Setting up the Innokin Gozee for each coil The box delivers 6 to 60 W and shows the wattage, the coil resistance and the length of each draw. Four settings are all it takes to match a Z Coil to the draw you want. ### Check the reading before the first draw Once the tank is screwed on, the main screen shows the resistance it has detected. A secondary screen, reached by holding the plus and power buttons together, gives the battery voltage and the coil resistance to more decimal places. Checking that the screen reads 1.2 ohm when you have fitted a 1.2 ohm coil stops you setting a wattage meant for a different coil. ### Raise the wattage in small steps Hold the plus or minus button until the wattage flashes, then adjust. Starting at the bottom of the coil's range and moving up in small steps is the safest method, since the top of the 1.6 ohm range, 12 W, sits below the bottom of the 0.8 ohm range, 15 W. ### Open or close the airflow at the base The airflow is set by turning the base of the GO Z+ tank, which Innokin says covers everything from MTL to RDL. For a tight draw, start almost closed and open it in small turns. Innokin pairs the 1.0 ohm Z Coil with more airflow, and the 0.3 ohm is built for RDL, so both call for a more open base. ### Set the draw cut-off The menu, opened by holding the plus and minus buttons together, sets the longest possible draw anywhere from 3 to 18 seconds, and the screen timeout from 5 to 180 seconds. A short cut-off stops an accidental press in a pocket from heating the coil for long. ## Changing a Z Coil without flooding the tank The Gozee manual sets one condition that is easy to forget, which is that the tank must be empty before the coil comes out. With the tank emptied, twist the base open, pull the old coil out, push the new one in and twist the base firmly closed. A new coil also needs five minutes after filling, according to the same manual, for the cotton to soak through. Filling is done from the top, by pushing the mouthpiece in the direction of the arrow to slide the top cap open, without going over the maximum level. ## Gozee or Gozee Nex for the same coils Innokin also sells a Gozee Nex. Both boxes accept every Z Coil, so the coils carry over from one model to the other. | Detail | Gozee | Gozee Nex | |---|---|---| | Battery | 2100 mAh | 3300 mAh | | Power | 6 to 60 W | 6 to 60 W | | Resistance range | 0.2 to 3.5 ohm | 0.1 to 3.5 ohm | | Body | PC and ABS, 73 g | zinc and aluminium alloy | | Screen | operating screen | 0.96 inch colour TFT | | Tank | GO Z+ | GO Z Nex, metal-reinforced airflow ring | The Nex adds an on and off switch underneath. Innokin does not publish its weight, whereas the original Gozee, plastic-bodied, is quoted at 73 g. ## FAQ Five questions that come up once the coil has been chosen. ### Do old Zenith coils fit the Gozee? Yes. Innokin has explained that boxes marked Zenith coils and boxes marked Z Coils contain the same coils, the Z Coil name having replaced the old one. A Zenith coil of the right value therefore fits the GO Z+. ### Can I fit a different tank to the Gozee? Yes, the box has a standard 510 thread and accepts coils from 0.2 to 3.5 ohm. Its 6 to 60 W range covers the low wattages of an MTL draw as well as the highest. ### How much e-liquid does the GO Z+ hold in the UK? Innokin quotes 3.5 ml for the international version and 2 ml for markets that follow the European tank rules. British regulations, as summarised on gov.uk, also cap e-cigarette tanks at 2 ml, so the 2 ml version is the only one that can be sold legally here. ### How much does the Gozee weigh? Innokin gives 73 g for the box, thanks to a double injection moulded chassis. That is where Innokin's own tagline for the kit, Featherweight Champion, comes from. ### How do I lock the wattage on the Gozee? Hold the minus and power buttons together, the action the manual describes as locking the screen. The padlock on the display turns from green to red, and the wattage stays put if a button is pressed by mistake. The same action unlocks it. ## Innokin Gozee, one coil for each way of drawing The Gozee does not change character with its box, it changes with its coil. A 1.2 or 1.6 ohm coil, the airflow nearly closed and a wattage at the bottom of the range give a tight draw. A 0.8 ohm adds warmth. The 1.0 and 0.3 ohm open things up towards RDL. For a measured MTL draw, an **Innokin Gozee** fitted with a 1.2 ohm Z Coil at around 10 to 12 W remains our starting point. The same wattage-range logic applies to the [Vaptio Cosmo 2 and its three power levels](/uk/vaptio-cosmo-2-guide/), where the coil also decides the real power. ## For tonight's reading - [Innokin Klypse range, which version to pick for a tight MTL draw](/uk/innokin-klypse-range/) - [Vaporesso Luxe X versions compared for a tight MTL draw](/uk/vaporesso-luxe-x-versions/) - [Vaporesso pods, which cartridge fits which device](/uk/vaporesso-cartridge-compatibility/) Written by Halo du Soir for adult readers only. Vaping products usually contain nicotine, which is addictive, and nicotine vaping products are not for sale to under-18s in the UK. Nothing on this page is a buying recommendation.